I had got tired of trying all the so-called ‘recommendations’ for fixing USB hub connectivity on the Raspberry Pi – including some from people who did not actually own one.. And yes, I do have the correct voltage power supply etc. etc… So – I was happy to see that there was -at least – a potential … Continue reading →
Just completed some basic tests with the new VMware Workstation 9.0 on my ‘test’ system (x86_64, Fedora 17)… Initial results.. Compiles and runs OK on kernel 3.4.9. Compiles OK, but causes general protection fault (with tombstone..) on kernel 3.5.2. (scroll down for the fix..) ……………………. /dev/vmnet: port on hub 8 successfully opened /dev/vmnet: open called by PID … Continue reading →
Odd problem with kernel 3.6-rc3 on the Dreamplug… I had the usual /etc/fstab entry, with both the ext4 root and vfat boot devices configured, but now – despite LVM / RAID not being enabled in the kernel, the init/systemd process insisted on treating the vfat device as a LVM/RAID device, and failing, and dropping to the ’emergency’ … Continue reading →
The Raspberry Pi repository on GitHub now has kernel 3.2.27 available, so I updated that with the 3.2.27-28 incremental patch, from ftp://ftp.kernel.org/pub/linux/kernel/v3.0/incr/ Now, the Pi is running Fedora 17 with kernel 3.2.28.. Fedora release 17 (Beefy Miracle) Kernel 3.2.28 on an armv6l (ttyAMA0) rgpi login: xxxx Password: Last login: Thu Jan 1 01:01:03 on ttyAMA0 [xxxx@rgpi ~]# … Continue reading →
The ‘default’ Fedora 13 system for ARM mounts the root as nfs.. To change it to the (correct) ext3, modify /etc/fstab as follows: # cat /etc/fstab /dev/mmcblk0p2 / ext3 defaults 1 1 /dev/mmcblk0p1 /boot vfat defaults 1 0 devpts /dev/pts devpts gid=5,mode=620 0 0 tmpfs /dev/shm tmpfs defaults 0 0 proc /proc proc defaults 0 0 sysfs … Continue reading →
For Fedora 13 on the APC, the console on the usb/uart connection will ‘vanish’ on boot, after ………. Starting sshd: [ OK ] To get it back, and allow login as root, add the following to /etc/securetty: ttyS0 and modify /etc/sysconfig/init: from ACTIVE_CONSOLES=/dev/tty[1-6] to ACTIVE_CONSOLES=”/dev/tty[1-6] dev/ttyS0″ To stop the (re)login prompt from appearing over the console boot … Continue reading →
In a vain attempt to get the APC’s antique kernel to – at least – work with Fedora 14, I had been applying the series of ‘incremental’ 2.6.32.x patches available – amongst other places – at http://ftp.monash.edu.au/pub/linux/kernel/v2.6/incr/ The kernel.org ftp site didn’t seem to have the full set.. This brought me as far as 2.6.32.27, which still … Continue reading →
In the hope of getting a newer version of Fedora Linux running, I have ‘updated’ the 2.6.32.9 APC kernel to 2.6.32.27.. This was achieved by the labour-intensive method of applying all the incremental kernel patches in sequence, and manually fixing any code that ‘failed’ the patch… So.. I am now running Fedora 13 with kernel 2.6.32.27 on … Continue reading →
As the currently-available source for the APC kernel does not include the necessary drivers for video output to a monitor (amongst other things..) but does include network drivers (Via Velocity..) it seemed logical that I could adopt the same approach to a graphical interface that I use for the Dreamplug (which is a real ‘headless’ device!). So.. … Continue reading →
After all the pioneering work done to get a compiled working version of the APC kernel by Mike Thompson from the Raspbian project, as described in a previous post, I now have Fedora Linux running on the APC. I had planned to be able to get Fedora 17 working, but the APC kernel (vintage 2010!) is just … Continue reading →