After noting the success of the XBMC team in getting high-quality video playback on the Raspberry Pi, I tried to see what was currently possible with the latest version of the APC kernel.. Sadly, the XBMC player is only available for the proprietary Pi Broadcom chipset.. I did try installing the binary-only Android APC player, but it … Continue reading →
Now that Fedora 13 and the APC kernel provide basic functionality, a brief summary of where you can get the ‘bits’… Assumptions: You will need to be reasonably adept at the following: 1. Cross-compiling and patching a Linux / ARM kernel, from source obtained from GitHub. 2. Formatting and partitioning an SD-card (FAT and EXT3..) 3. Installing … Continue reading →
After compiling the latest release of the APC-8750 kernel source code, I am pleased to find that video/HDMI output to an hdmi-attached monitor now works! So… I now have XFCE Desktop running on the APC under Fedora 13, and Kernel 2.6.32.9-apc.. A bit old, but – it works!
Continue reading →Odd problem with kernel 3.6-rc3 on the Dreamplug… I had the usual /etc/fstab entry, with both the ext4 root and vfat boot devices configured, but now – despite LVM / RAID not being enabled in the kernel, the init/systemd process insisted on treating the vfat device as a LVM/RAID device, and failing, and dropping to the ’emergency’ … Continue reading →
The Raspberry Pi repository on GitHub now has kernel 3.2.27 available, so I updated that with the 3.2.27-28 incremental patch, from ftp://ftp.kernel.org/pub/linux/kernel/v3.0/incr/ Now, the Pi is running Fedora 17 with kernel 3.2.28.. Fedora release 17 (Beefy Miracle) Kernel 3.2.28 on an armv6l (ttyAMA0) rgpi login: xxxx Password: Last login: Thu Jan 1 01:01:03 on ttyAMA0 [xxxx@rgpi ~]# … Continue reading →
After all the fuss with ancient versions of Linux on the APC, I now have the very latest Linux – 3.6-rc3 – running on the Dreamplug..: Fedora release 17 (Beefy Miracle) Kernel 3.6.0-rc3 on an armv5tel (ttyS0) rgdreamplug login: …………. # uname -a Linux rgdreamplug 3.6.0-rc3 #1 Fri Aug 24 00:20:25 BST 2012 armv5tel armv5tel armv5tel GNU/Linux … Continue reading →
The ‘default’ Fedora 13 system for ARM mounts the root as nfs.. To change it to the (correct) ext3, modify /etc/fstab as follows: # cat /etc/fstab /dev/mmcblk0p2 / ext3 defaults 1 1 /dev/mmcblk0p1 /boot vfat defaults 1 0 devpts /dev/pts devpts gid=5,mode=620 0 0 tmpfs /dev/shm tmpfs defaults 0 0 proc /proc proc defaults 0 0 sysfs … Continue reading →
For Fedora 13 on the APC, the console on the usb/uart connection will ‘vanish’ on boot, after ………. Starting sshd: [ OK ] To get it back, and allow login as root, add the following to /etc/securetty: ttyS0 and modify /etc/sysconfig/init: from ACTIVE_CONSOLES=/dev/tty[1-6] to ACTIVE_CONSOLES=”/dev/tty[1-6] dev/ttyS0″ To stop the (re)login prompt from appearing over the console boot … Continue reading →
In a vain attempt to get the APC’s antique kernel to – at least – work with Fedora 14, I had been applying the series of ‘incremental’ 2.6.32.x patches available – amongst other places – at http://ftp.monash.edu.au/pub/linux/kernel/v2.6/incr/ The kernel.org ftp site didn’t seem to have the full set.. This brought me as far as 2.6.32.27, which still … Continue reading →
In the hope of getting a newer version of Fedora Linux running, I have ‘updated’ the 2.6.32.9 APC kernel to 2.6.32.27.. This was achieved by the labour-intensive method of applying all the incremental kernel patches in sequence, and manually fixing any code that ‘failed’ the patch… So.. I am now running Fedora 13 with kernel 2.6.32.27 on … Continue reading →