Kernel 4.6-rc5 is out, and brief details of changes from -rc4 are here: http://lkml.iu.edu/hypermail/linux/kernel/1604.3/00178.html Kernel 4.6 seems to have a habit of continuing later-rc breakages with VMware and NVIDIA, compared to previous kernel releases.. The VMware 12 fix for 4.6-rc4 (see https://rglinuxtech.com/?p=1706 ) still works OK with 4.6-rc5, but even the latest NVIDIA driver – 364.19 breaks … Continue reading →
Thanks to Justin Palermo, there is a patch for VMware 12 vmmon and vmnet problems he identified with the later Kernel 4.6-rcs. See comments on my earlier 4.6-rc1 article for details: https://rglinuxtech.com/?p=1679 I have applied the patch to VMware 12.1.0, on Kernel 4.6-rc4, and VMware now compiles and runs OK.. Robert Gadsdon. April 22, 2016.
Continue reading →I had been running Kernel 4.6-rc2 on the Radxa Rock2 without any issues, and decided to update to recently-released Kernel 4.6-rc4.. Brief details of changes from -rc3 are here: http://lkml.iu.edu/hypermail/linux/kernel/1604.2/00610.html The boot failed, and I then compiled/installed 4.6-rc3 to see if that would have been OK, and it was.. I then noticed something odd in the failed … Continue reading →
Updated the Rock2 to Kernel 4.6-rc1: ……… Fedora 23 (Twenty Three) Kernel 4.6.0-rc1 on an armv7l (ttyS2) ……………….. # uname -a Linux rgrock2 4.6.0-rc1 #1 SMP Sun Mar 27 03:47:06 EDT 2016 armv7l armv7l armv7l GNU/Linux The stmmac Ethernet driver bug from 4.5 Final has still not been fixed, and the driver code has changed in 4.6-rc1, … Continue reading →
Just installed Kernel 4.6-rc1 on the test system. Depending on your configuration, you may encounter a compilation error: CC drivers/thermal/mtk_thermal.o drivers/thermal/mtk_thermal.c: In function ‘mtk_thermal_probe’: drivers/thermal/mtk_thermal.c:560:8: error: implicit declaration of function ‘device_reset’ [-Werror=implicit-function-declaration] ret = device_reset(&pdev->dev); ^ cc1: some warnings being treated as errors ……………………………. This is due to a Mediatek thermal driver being ‘selected’ by default (and … Continue reading →
Kernel 4.5-rc7 had booted successfully on the Radxa Rock2, but 4.5 Final failed, as the SDcard was ‘loaded’ just too late: mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) dwmmc_rockchip ff0f0000.dwmmc: 1 slots initialized ……………………… VFS: Cannot open root device “mmcblk1p1” or unknown-block(0,0): error -6 ………………………… Kernel panic – … Continue reading →
Recently took delivery of a Radxa Rock2 ARMv7 system, based on the RX3288 Cortex A17 chipset.. The system comes with a version of Android installed on the onboard eMMC, but I managed – after a bit of work – to install Fedora 23 on an SDcard and get it to boot onto that.. At this point, I … Continue reading →
I recently acquired a vintage (2006?) Minolta Elite 5400 II scanner, and – according to the VueScan support info, I needed to ”set up libusb device protections”.. That info included a link to a somewhat ancient SANE USB support page – last changed in 2003!.. That rang a bell, and I guessed that I had to mess … Continue reading →
I did a clean install of Fedora 23 on my new ‘built from recycled components‘ crash-and-burn test system recently, and all went reasonably well – apart from – apparently – having to re-partition an already-partitioned drive (!)… After booting for the first time, I found that a ‘bridged’ network link – virtbr0 – was active.. As I … Continue reading →
Installed ZoneMinder ( https://zoneminder.com ) for some IP and WiFi cameras, and the first thing to remember is to not use the Fedora version! This is due to the lack of ffmpeg and vlc support in that version, which makes the software somewhat less than useful.. Fortunately, there is good Fedora support, with a fully-functional version – … Continue reading →